Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Parts & Accessories

$714.00
Optimize your Zipp wheels with CeramicSpeed Hub Bearings to benefit from reduced friction and increased performance. The result is higher speed with the same effort as well as a higher top speed. CeramicSpeed Wheel Bearings have a proven lifetime, which is 3-5 times longer than standard bearings. All components are optimized for low friction and prolonged lifetime. This wheel kit is compatible with 1st generation non-disc Zipp NSW (before mid-2018). In The Box - 4 x 61803 bearings - 1 x 61903 bearing - 1 x 61804 bearing - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet
$149.00
CushCore is an engineered foam insert to be mounted inside a tire, designed to absorb impacts, reduce vibration, and increase lateral stability. These characteristics translate to a more controlled, comfortable, and faster ride. - The system is designed to be used with tubeless-ready or tubeless converted rims and tires and is compatible with tubeless tire sealants - A specially designed tubeless air valve is included with each insert; allowing air to move through the valve without becoming obstructed by the insert - The insert divides the inner volume of the tire in half, maintaining air underneath the tread and the foam insert next to the rim - Fits tire widths 2.1 – 2.6" and rims with internal width 22 – 35mm Includes: - 2 CushCore Inserts - 2 CushCore Tubeless Air Valves - 4 Rim Stickers - Installation Instructions
$119.99
Upgrade or refresh your Bontrager wheels. Genuine replacement parts Whether you're looking to upgrade to the newest and freshest drivetrain or simply hoping to refresh your trusty wheelset, Trek Genuine Replacement Parts have you covered. - Replacement parts for Bontrager hubs using the DT 240 platform - Compatible with all Bontrager wheels with DT 240 hub internals - For use with Shimano MICRO SPLINE cassettes - Includes 12mm thru-axle end cap
$99.99
Upgrade or refresh your Bontrager wheels. Genuine replacement parts Whether you're looking to upgrade to the newest and freshest drivetrain or simply hoping to refresh your trusty wheelset, Trek Genuine Replacement Parts have you covered. - Replacement freehub body - Compatible with Bontrager Rapid Drive 108 hubs - Pawls and springs sold separately - Install 3 pawls/springs for 54 tooth engagement or 6 pawls springs for 108 tooth
$92.40
DT Swiss tubeless ready tape seals the rim for tubeless applications and also works well as rim tape for tube-type set ups. - Highly resistant adhesive tape works as a rim tape and airseal
$79.99 - $85.00 $79.99 - $85.00 On Sale
Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed. - 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration - Chromed steel bearings - Wide bearing stance and axle design reduces flex and adds durability - Low drag main seal prevents contamination and reduces resistance - Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components
$79.99
This conversion kit allows you to use SRAM's 11-speed mountain cassette on your Stan's NoTubes wheels. Each kit includes an XD freehub, spacer, drive side end cap, and three sealed bearings.
$13.95 - $79.95
Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).
$74.99
Dynaplug Air is the only tool of it's kind in the world. Plug your tubeless Mountain/Gravel tire and quickly air it up with CO2 at the same time! Here's how it works: 1) Insert repair nozzle into puncture. 2) Open regulated air valve to achieve desired pressure. 3) Close valve and remove tool. Plug will hold air and seal puncture simultaneously. Dynaplug Air Kit includes: - Insertion Tube for MTB/Gravel (25mm length) - x4, Brass soft nose tip repair plugs, for Mountain/Gravel tires only - Neoprene pouch - CO2 hose for valve stem (CO2 cartridges are NOT included) Please note—the MTB tire Plugs are about twice the length of the Road style plug. So the MTB tire plugs should not be used for Road tire repairs.
$73.99
Upgrade or refresh your Bontrager wheels. Genuine replacement parts Whether you're looking to upgrade to the newest and freshest drivetrain or simply hoping to refresh your trusty wheelset, Trek Genuine Replacement Parts have you covered. - Replacement freehub body - Compatible with Bontrager Entry-level hubs
$72.00 $79.00 9% Off
- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Drive Side Axle End Cap
$65.99
The Muc-Off Ultimate Tubeless Kit contains everything needed to get a tubeless-ready wheelset set up and ready to roll. Each Kit contains Tubeless Rim Tape, two CNC-machined black tubeless valves and two pouches of No Puncture Hassle Tubeless Sealant.
$65.00
Shimano, FH-M828/788/678/648, Freehub body, Y3TH98050
$59.00
Maxle Ultimate Lever Assembly - Fits Maxle Ultimate B1 - Includes lever section only - Suitable for suspension forks
$56.00
Trainer ready. Keep the ride going by putting your Cannondale on a trainer with the 2-in-1 trainer axle. Where it thrives: The open road, on the trainer What it's built for: Versatility, convenience Highlights: - Fit your Cannondale road bike to any indoor trainer Removable end caps for outdoor riding - Compatible with Cannondale road bikes that utilize Speed Release dropouts
$54.99
Upgrade or refresh your Bontrager wheels. Genuine replacement parts Whether you're looking to upgrade to the newest and freshest drivetrain or simply hoping to refresh your trusty wheelset, Trek - Replacement freehub body - Compatible with Kovee Elite 23, and Duster Elite wheels
$54.00 - $54.99
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
$52.99
Pinhead offers you the ideal solution to bicycle wheel theft. - Includes x2 locknuts (26 tpi) - Replaces 3/8" axle nut and locks wheel to frame/fork - Includes Solid Axle type key - 13g
$4.24 - $52.79
Ease of use, lightweight, and optimum performance in a single product. The DT Pro Head shape, combined with both a torx and a square tool interface, makes wheel building a lot easier. The spherical contact surface aligns the nipple perfectly with the spoke. All-brass nipples are recommended for e-bike use. Weight: starting at 26g for 64 nipples.
$38.00 - $50.00
SRAM's Quick Releases hold your wheel tightly in place, are built for ease of use and made to last, too. You get a front and rear quick release.
$49.99
Tannus Armour Tubeless inserts are the result of years of top level multi-cell foam manufacturing mixed with extensive professional riding experience. At the heart of Tannus is the patented Aither Technology; a multi-cell foam compound that forms the structure of the Armour. The inserts are designed to displace small impacts while offering a spring-like rebound for a smooth yet playful ride. - 3% Faster than standard tubeless - Flexible sidewall stabilizing "Wings" for smoother ride quality, with 50% more vibration damping - 20mm of rim protection - Not a sealant sponge – keeps sealant where it belongs - Easy Installation (5 Minutes, No tools required) - 150g - About as much as a standard tube (a little lighter)
$42.00 - $48.00
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
$11.50 - $48.00
We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels
$47.70
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted. - DT Swiss Rear End Caps - QR x 135/142mm
$47.70
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
$16.89 - $45.99
The buyer's choice for wheel builders looking to save weight. The nipples are available with or without DT Pro Lock, a patented liquid inside the nipple thread that makes the connection between the nipple and spoke extremely durable. It pairs perfectly with any wheel, though all-brass nipples are recommended for e-bike use. - Weight: starting at 20g for 64 nipples
$39.99 - $41.99
These original replacements will get your wheels working like new. - Alloy thru-axle that can be used with a 6mm hex wrench or with a lever - Keep it light by removing the lever and instead use a 6mm hex wrench - Keep it convenient by keeping the lever inside the axle - Lever is held securely by internal O-ring - Lever sold separately
$39.99 - $41.99
These original replacements will get your wheels working like new. - Alloy thru-axle that can be used with a 6mm hex wrench or with a lever - Keep it light by removing the lever and instead use a 6mm hex wrench - Keep it convenient by keeping the lever inside the axle - Lever is held securely by internal O-ring - Lever sold separately
$5.50 - $41.99 $5.50 - $42.00 On Sale
- Syntace x-12 Rear axle standard creates a stiffer and lightweight rear end - Syntace x-12 Parts are only compatible with frames that have Syntace x-12 Dropouts
$40.00
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 126mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 137mm - 1 axle per bag
Page 1 of 4 Next page